Resistive Load 0-220VAC Regulator Effecvtive Generator Voltage Regulator Zkd-2A

• Customization: Available
• Task: Adjust
• Structure: Combination
• Model NO.: ZKD-2A
• Mathematical Model: Linear
• Signal: Continuous
• Function: Automatic Control, Monitoring, Measurement
• Certification: ISO: 9001, CE
• Condition: New
• Customized: Non-Customized
• Material: Industrial Flame Retardant Plastics
• Overall Dimension(W*L*H): 72*72*125mm
• Opening Size Dimension: 68*68
• Voltage: 220V AC±15%
• Frequency: 50Hz/60Hz
• Power Consumption: 3W
• Transport Package: Carton
• Specification: ZKD-2A
• Trademark: Aoyi
• Origin: China
• HS Code: 9030390000
• Production Capacity: 10000 Pieces/Year
• Package Size: 47.00cm * 43.00cm * 36.00cm
• Package Gross Weight: 10.000kg

Product Description

Detailed Photos

Product Specifications

Maximum conduction angle for Phase-Shift Trigger		≥150°
Dimension(mm)	Opening size dimension	68*68
	Overall dimension(w*l*h)	72*72*125
Power supply	Voltage	220V AC±15%
	Frequency	50Hz/60Hz
Power Consumption		3W
Working environment	Working temperature	0ºC~50ºC
	Relative humidity	in non-corrosive gas occasions with relative humidity≤85%
Output trigger pulse		amplitude≥ 3V, width ≥ 50μs (when 20Ω load)

Wiring Diagram

Warning

1. Connect the output, feedback, power supply, ground wire, and electric furnace according to the wiring diagram. The load phase must be the same as the voltage regulator power supply phase (ie, in phase), otherwise the voltage regulator will be damaged.
2. The withstand voltage of the thyristor must be more than 2.5 times the supply voltage (Eg: the voltage withstand voltage of the thyristor must be no lower than AC600V when use voltage at 220V). The thyristor rated current must be more than 1.5 times the current actually used. The thyristor should be equipped with a large enough heat sink, and pay attention to the ventilation and heat dissipation to ensure that the temperature of the thyristor does not exceed 70 °C under any circumstances.
3. Fuse FU must be connected to the input terminal of phase line when connected with the anode of thyristor in series and shall not be connected to other positions.
4. The heat sink of thyristor should be equipped properly against electric shock and short circuit between thyristor electrodes.                               
5. The ammeter must be in series with the anode of thyristor and do not let the trigger signal pass through the ammeter if the ammeter is connected.
6. Trigger signal lines which are used to connect this device with the thyristor should be separate from other wires and keep it as short as possible in case of the thyristor out of control due to eternal interference.

Operation and Adjustment

1. Open the "POWER", the meter begins working.
2. Adjust the addend key "∧"or subtracted key "∨"on the panel to make the displayed voltage (voltage on the load) meet required value.
3. The regulator uses negative voltage feedback, half-wave power is strictly forbidden to be supplied to the load, or the DC power on the load will damage the transformer inside the machine, and the single-sided conduction of the thyristor  should not happen in normal use.
4. Do not drive inductive loads such as induction furnaces and step-down transformers in case of damaging thyristor. 
5. In the event that the thyristor cannot be fully turned on or the displayed output value seriously changes. The reason is mistaking connection of trigger signal lines and exchanging the two trigger signal output lines can solve.    

Others
The instrument should be stored in a place where is dry, ventilated, non-corrosive gas, and the ambient temperature and relative humidity should meet the technical requirements

Company Profile

Established in 2007, Shanghai/Huangshan Aoyi Electric Co., Ltd is a manufacturer and trader specialized in the research, production and development of Temperature control electric company. Our products include pointer meters, current and voltage meters, solid state relays, SCR power regulators, voltage regulators and intelligent temperature controller.

We are located in Shanghai, China's trade center, more than 100 outstanding employees. All of our products have obtained CCC, CE and passed ISO9001 international quality standards test. As a result of our excellent products and outstanding customer service, we have established a global sales network reaching China, Southeast Asia, Europe, America and other countries. With the strong support of business cooperation friends around the world like you, Our sales are growing every year, we have achieved sales of tens of millions in 2019, and we will keep it up in the future.

If you are interested in any of our products or would like to place an order, please get free to contact us. We are ready and looking forward to forming successful business relationships with new clients around the world in the near future. Let's achieve success together and take our business one step further

Zhang Qifa, the founder of Shanghai Aoyi Electric Co., Ltd, has been engaged in the temperature control electronics industry for more than 30 years. His business philosophy is quality first, integrity management, scientific and technological innovation, and welcomes friends from outside with excellent products and services.

Factory Introduction

Contact with Us